Photos 2014

People

Collecting GlueX Data Dec 2014

Tagger Microscope

TAGM shielding Dec 2014	TAGM shielding Dec 2014	TAGM shielding Dec 2014	TAGM shielding Dec 2014	Initial TAGM Fiber Installation Sep 2014	Initial TAGM Fiber Installation Sep 2014
Initial TAGM Fiber Installation Sep 2014	Fiber bundle in straightening setup May 2014	"Fish tank" heating unit May 2014	Fiber polishing May 2014	Splicing unit May 2014	A comparison between lightguide and scintillator cladding on fibers May 2014
The Dark Box May 2014	Fibers in intermediate dark box May 2014	Full straightening setup May 2014	5x6 Fiber matrix May 2014	Heat treating pipe May 2014	Scintillating fibers prior to polishing Feb 2014
Scintillating fibers after polishing Feb 2014	A bundle being end-milled in the physics machine shop Jan 2014	end mill and fibers Jan 2014

Whole detector

The GlueX Detector, October 2014 Oct 2014	The GlueX Dectector October 2014 Oct 2014	Picture taken from Hall D cam on October 1 2014 Oct 2014	The GlueX Detector, October 2014 Oct 2014	The GlueX Dectector October 2014 Oct 2014	Overview of GlueX taken on August 1, 2014 Aug 2014
Hall D in May 2014 May 2014

CDC

Curtis Meyer looking at the installed CDC, October 2014 Oct 2014	CDC in bore Apr 2014	CDC smiling Apr 2014	CDC in bore Apr 2014	CDC on installation rails Apr 2014	CDC on installation rails Apr 2014
CDC on installation rails Apr 2014	CDC move from EEL Mar 2014	CDC loaded onto truck for transport to the hall Mar 2014	CDC coming down the ramp Mar 2014	CDC in the hall Mar 2014

Start Counter

Light tightening outer cone Sep 2014	Fully cabled Start Counter Sep 2014	Fully constructed Start Counter undergoing light tightening test Sep 2014	Fully cabled Start Counter upstream Sep 2014	Start Counter fully inserted into CDC Sep 2014	Start Counter fully inserted into CDC and target cart Sep 2014
Start Counter being inserted into CDC Sep 2014	Start Counter almost fully inserted into CDC Sep 2014	Start Counter mounted to the commissioning target Sep 2014	Start Counter mounted to the commissioning target and CDC Sep 2014	Start Counter in EEL 126 Sep 2014	Start Counter without mounting rings Sep 2014
Start Counter without mounting rings facing down stream Sep 2014	Fully light tight Start Counter Sep 2014	Light tightening inner cone Sep 2014	Completed Start Counter at FIU Aug 2014	Lenzer visit to Eljen Jan 2014

Emergency and safety

Keys for controlled access in labyrinth into Hall D. Sep 2014	Communications at entrance to labyrinth from stair case. Sep 2014	Severe Weather emergency shelter at the base of the stairs facing the labyrinth Sep 2014	Emergency exit to the outside at top left of stairs to the Counting Room. Sep 2014	Side door to truck ramp. Power kill, fire pull station Sep 2014	CARM sensors at the top of the staircase. Sep 2014
Hall D door next to truck ramp. Exit buttons and fire extinguisher Sep 2014	Emergency buttons, left of white board in Counting Room. Power kill button and PSS emergency beam stop. Sep 2014	East wall near truck ramp in Hall D. Emergency equipment. Sep 2014	Button and fire extinguisher right of white board in Counting Room. Sep 2014	Fire extinguisher on south end of FCAL platform Sep 2014	Power kill buttons inside rack room. Target compressor, solenoid, PS and sweep power (to be labeled). Sep 2014
Entrance to collimator cave. PSS emergency stop on far wall. Sep 2014	Fire alarm control panel and fire extinguisher at the entrance to the Counting House. Sep 2014	Run Safe box, fire extinguisher middle of south wall, Hall D Sep 2014	Fire pull station at the entrance vestibule to the Counting House. Sep 2014	Run Safe box on north wall, west end, Hall D Sep 2014	Door to staircase and Counting Room. North wall, Hall D Sep 2014
Door to staircase and Counting Room. Right side with exit buttons, power kill button and fire extinguisher Sep 2014	Run Safe box on east wall, north side, Hall D. Sep 2014	Exit buttons, right side of door exiting labyrinth of Hall D. Sep 2014	Door next to truck ramp in Hall D Sep 2014	Accelerator status with fire and flammable gas alarms Sep 2014

Active Collimator

Active collimator faceplate Aug 2014

Assembly of active collimator tungsten wedges Aug 2014

Completed assembly of active collimator wedges Aug 2014

Target

Target on installation rails Jul 2014

Target on installation rails Jul 2014

Target on installation rails Jul 2014

Target on installation rails Jul 2014

TOF

GlueX TOF being lifted into location Apr 2014	TOF Ready for Lift Off Apr 2014	The Garnet & Gold Detector (aka TOF) in Hall D Mar 2014	Assembling the first TOF modular plane Mar 2014	The TOF with both modular planes assembled Mar 2014	Installing the TOF support frame Mar 2014
The TOF with second modular plane assembled Mar 2014	Squeezing TOF modules Mar 2014	Assembling the second TOF modular plane Mar 2014	Assembling the TOF support frame Mar 2014	Inital Design for holding TOF modules Feb 2014	TOF channel support studs modification Feb 2014
Complete installation of the first TOF modular plane Feb 2014	over flexing of the TOF modules Feb 2014	Hussein and Paul in the Hall putting together the TOF Jan 2014	The installation of the first TOF modular frame Jan 2014

Diamond Radiator

Zygo Image if U300_30 Mar 2014	Initial Pulse Geometries in Diamond Jan 2014	U300_150 CHESS Whole Crystal Rocking Curve Jan 2014	New Beam Geometry Jan 2014	U300_40 CHESS Jan 2014	First Trenches Milled in Diamond Jan 2014
U300_40 CHESS Whole Crystal Rocking Curve Jan 2014	Zygo of U300_240 Jan 2014	Ablation Plume Jan 2014	CHESS Goniometer Jan 2014	Zygo Surface Variation of U300_240 Jan 2014	Ionization of Air Between Two Lenses Jan 2014
S300_30 CHESS Jan 2014	S300_30 CHESS Whole Crystal Rocking Curve Jan 2014	S300_90 CHESS Jan 2014	S300_90 CHESS Whole Crystal Rocking Curve Jan 2014	S300_150 CHESS Jan 2014	Initial Picture Frame Raster of U300_30 Jan 2014
S300_150 CHESS Whole Crystal Rocking Curve Jan 2014	U300_150 CHESS Jan 2014	Zygo Cross Sectional Plot of U300_240 Jan 2014

FDC

FDC completely cabled and pushed inside the magnet (just a dry run). Jan 2014